TechMende.com
Easy Technology Tips, Tricks & Guides

How to Fix a Mouse Scroll Wheel Jumping Up and Down

Image Credit: Orkhan Aliyev/YouTube

Is your mouse scroll wheel always jumping up and down and making it hard to control the cursor when you scroll? An ill-fitting scroll wheel can easily ruin your gaming experience (or work productivity). Most often, the mouse encoder causes your mouse scroll to be unstable and jumpy. In some cases, the scroll wheel itself is to blame.


As it’s pretty easy to fix, there’s no need to replace your mouse if you’re experiencing the same problem. We’ll guide you through a step-by-step process for fixing mouse scroll wheel instability.


As the copper wires on the coil inside the mouse encoder wear away, the spring loses its ability to press the encoder coil into perfect contact with the wheel. As a result, the mouse scroll wheel becomes jumpy. Additionally, if the scroll wheel becomes too loose, you may experience the same problem.

To fix a jumpy scroll wheel, one option is to buy yourself a new encoder and replace it with the existing one in your mouse, and all will be set. However, if you don’t want to take that route, you can fix the encoder and the loose scroll wheel yourself. In this guide, we will show you how you can do that.

There is no need for special equipment to fix the mouse scroll wheel, nor do you need to be an avid DIYer. To fix a jumpy mouse scroll wheel, you only need a screwdriver to unscrew the screws holding your mouse in place. Besides, you may need to replace your old encoder if worn out.

Bring out the screwdriver you have at home, or buy a new one, and move on to fixing your mouse scroll wheel. Check out our review of the Wowstick electric screwdriver if you’re interested in purchasing a new one.

It is important to note that the instructions below are for the Razor Naga 2014 model. The steps to fix the jumpy scroll wheel could vary depending on the brand and model of the mouse and the type of encoders it has.

Here’s a step-by-step guide for how to stop your mouse scroll wheel from jumping up and down.

1. Disassemble the Mouse Casing

Person Unmounting the Screws to Disassemble the Mouse Casing
Image Credit: TechClub/YouTube
 

The first step is to disassemble the mouse casing by unscrewing all the screws. To do so, remove any pads covering your mouse screws so you can see them. When the screws are visible, use a screwdriver to unscrew them and place them in a safe location.

If there aren’t any screws left, you should be able to remove the top panel of the mouse casing and reveal the internal circuit board. After that, you will need to unplug all circuit connections.

2. Carefully Unplug the Circuit Connections

Your mouse may have a connection that connects the LED on the top panel of the casing with the main circuit. If there is, unplug it first and carefully place the top panel of your mouse casing on your desk. Remove the rest of the necessary connections from the mouse circuit as well.

Person Unplugging the LED Cable Connected to the Upper Panel of the Mouse Casing
Image Credit: TechClub/YouTube

Even though removing your mouse’s circuit from the lower panel is unnecessary, if you want to do that, make sure there are no screws attached. If there are any, remove them and take the circuit off the bottom panel of your mouse. Alternatively, you can unmount the scroll wheel directly without unmounting the circuit.

3. Unmount the Scroll Wheel

Person Unmounting the Scroll Wheel From Mouse
Image Credit: TechClub/YouTube

Unplug the encoder attached to the scroll wheel from the main board before unmounting the scroll wheel. Then, unplug any other connections, unscrew any screws, and take out the scroll wheel. After you have unmounted the scroll wheel, remove the encoder and proceed to the next step: fix the encoder.

4. Fix the Encoder Assembly

Person Showing the Mouse Encoder Assembly
Image Credit: TechClub/YouTube

When you unmount the encoder, you need to open the encoder box to see the encoder coil. To do so, press against the D-shaped metal spring inside the encoder box and remove the metal cover. Here are the components you may find in the box:

  • D-shaped metal piece acting as a spring.
  • Copper wires wrapped around a coil.

The copper wires wrapped around the coil can wear away with time. Consequently, the metal piece, acting as a spring, fails to push it to make perfect contact with the encoder bottom. Most of the time, this is what causes a jumpy scroll wheel.

To fix it, remove the spring and coil from the encoder assembly and wipe off any dust. Once that’s done, put the encoder back in and tighten the spring more to exert more pressure on the encoder coil. For the coil to maintain its position, the spring must fully push it. After you’ve done that, reassemble the mouse and test it.

Person Showing the Fixed Mouse Encoder
Image Credit: TechClub/YouTube

If the issue persists, there might be a problem with the scroll wheel hub. So, fixing the encoder coil spring assembly may not help.

5. Wrap a Small Piece of Paper Around the Scroll Wheel Hub

To fix the loose scroll wheel, wrap a small piece of paper around the scroll wheel hub before inserting it into the encoder. Doing so will reduce the gap between the encoder coil and the scroll wheel hub, which will keep the scroll wheel stable. Once you do that, you will no longer experience a jumpy scroll wheel.

However, what if everything listed above fails to stabilize the scroll wheel? In that case, you should invest in a new encoder.

Buy a New Encoder

Our guide will help you fix the jumpy scroll wheel, but if it still doesn’t work, purchasing a new encoder should be your last resort. Find out what type of encoder your mouse has and buy it. Replace the old encoder with the new one; hopefully, it will fix the problem.

The cost of an encoder is very low, so it won’t break the bank to buy one. Additionally, replacing the encoders is far more cost-effective than replacing the entire mouse, so it’s the best option. Nevertheless, if the issue persists and replacing the encoder does not resolve it, consider buying a new good-quality gaming mouse.

A jumpy scroll wheel can make us miss our targets when playing shooting games. Scrolling also becomes very annoying with a poor response from your mouse scroll wheel. We hope you’ll be able to solve the jumpy scroll wheel problem by following our instructions.

Remember, sometimes the problem is with your operating system rather than the hardware. When that happens, you’ll need to apply the operating system-level fixes to stabilize scrolling.

DIY,Computer Mouse Tips,DIY Project Tutorials,Troubleshooting

>>Here is the Original Post!

Leave A Reply

Your email address will not be published.